Description
3 Inch X 27 Ft Ratchet Strap W/ Flat Hook
* High Quality Ratchet Strap* With Flat Hook (Breaking Strength 17,000 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 27 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
3 Inch X 30 Ft Ratchet Strap W/ Flat Hook
* High Quality Ratchet Strap* With Flat Hook (Breaking Strength 17,000 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 30 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
3 Inch X 40 Ft Ratchet Strap W/ Flat Hook
* High Quality Ratchet Strap* With Flat Hook (Breaking Strength 17,000 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 40 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
3 Inch X 27 Ft Ratchet Strap W/ Grab Hook Assembly
* High Quality Ratchet Strap* With Grab Hook Assembly (Breaking Strength 16,200 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 27 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
3 Inch X 30 Ft Ratchet Strap W/ Grab Hook Assembly
* High Quality Ratchet Strap* With Grab Hook Assembly (Breaking Strength 16,200 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 30 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
3 Inch X 40 Ft Ratchet Strap W/ Grab Hook Assembly
* High Quality Ratchet Strap* With Grab Hook Assembly (Breaking Strength 16,200 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 40 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
3 Inch X 27 Ft Ratchet Strap W/ J Hook Assembly
* High Quality Ratchet Strap* With J Hook (Breaking Strength 10,000 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 27 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
3 Inch X 30 Ft Ratchet Strap W/ J Hook Assembly
* High Quality Ratchet Strap* With J Hook (Breaking Strength 10,000 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 30 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
3 Inch X 40 Ft Ratchet Strap W/ J Hook Assembly
* High Quality Ratchet Strap* With J Hook (Breaking Strength 10,000 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 40 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
3 Inch X 27 Ft Ratchet Strap W/ 18 Inch Chain Anchor
* High Quality Ratchet Strap* With 18 Inch Chain Anchor (Breaking Strength 16,200 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 27 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
3 Inch X 30 Ft Ratchet Strap W/ 18 Inch Chain Anchor
* High Quality Ratchet Strap* With 18 Inch Chain Anchor (Breaking Strength 16,200 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 30 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
3 Inch X 40 Ft Ratchet Strap W/ 18 Inch Chain Anchor
* High Quality Ratchet Strap* With 18 Inch Chain Anchor (Breaking Strength 16,200 Lbs)
* Strap Breaking Strength: 18,000 Lbs
* Strap WLL: 5,000 Lbs
* Resin-Coated Polyester Webbing
* Yellow With Black Stencil
* 40 Foot Length
* 3 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
** This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Additional Information
Length Options: |
360 Inch |
Material Options: |
Polyester |
Product Type: |
Cargo Control |
Width Options: |
3 Inch |
Color: |
Yellow |
Rating: |
18000 LBS |
Make: |
Universal Items |
