Description
Yellow W/ Black Stencil 2 Inch X 12 Ft 4K Ratchet Strap W/ Butterfly Fittings
* High Quality Ratchet Strap* Includes 2 Piece Butterfly Fittings
* Assembly WLL: 416 Lbs
* Breaking Strength: 1,250 Lbs
* Heavy-Duty Polyester
* Yellow With Black Stencil
* 12 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Gray W/ Black Stencil 2 Inch X 16 Ft 4K Ratchet Strap W/ Butterfly Fittings
* High Quality Ratchet Strap* Includes 2 Piece Butterfly Fittings
* Assembly WLL: 416 Lbs
* Breaking Strength: 1,250 Lbs
* Heavy-Duty Polyester
* Gray With Black Stencil
* 16 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Blue W/ Black Stencil 2 Inch X 20 Ft 4K Ratchet Strap W/ Butterfly Fittings
* High Quality Ratchet Strap* Includes 2 Piece Butterfly Fittings
* Assembly WLL: 416 Lbs
* Breaking Strength: 1,250 Lbs
* Heavy-Duty Polyester
* Blue With Black Stencil
* 20 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Yellow W/ Black Stencil 2 Inch X 12 Ft 4K Ratchet Strap W/ F Wire Hooks
* High Quality Ratchet Strap* Includes Wire F Hooks
* Assembly WLL: 500 Lbs
* Breaking Strength: 1,500 Lbs
* Heavy-Duty Polyester
* Yellow With Black Stencil
* 12 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Gray W/ Black Stencil 2 Inch X 16 Ft 4K Ratchet Strap W/ F Wire Hooks
* High Quality Ratchet Strap* Includes Wire F Hooks
* Assembly WLL: 500 Lbs
* Breaking Strength: 1,500 Lbs
* Heavy-Duty Polyester
* Gray With Black Stencil
* 16 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Blue W/ Black Stencil 2 Inch X 20 Ft 4K Ratchet Strap W/ F Wire Hooks
* High Quality Ratchet Strap* Includes Wire F Hooks
* Assembly WLL: 500 Lbs
* Breaking Strength: 1,500 Lbs
* Heavy-Duty Polyester
* Blue With Black Stencil
* 20 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Yellow W/ Black Stencil 2 Inch X 12 Ft 4K Ratchet Strap W/ E Fittings
* High Quality Ratchet Strap* Includes E Fittings
* Assembly WLL: 1.466 Lbs
* Breaking Strength: 4,400 Lbs
* Heavy-Duty Polyester
* Yellow With Black Stencil
* 12 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Gray W/ Black Stencil 2 Inch X 16 Ft 4K Ratchet Strap W/ E Fittings
* High Quality Ratchet Strap* Includes E Fittings
* Assembly WLL: 1.466 Lbs
* Breaking Strength: 4,400 Lbs
* Heavy-Duty Polyester
* Gray With Black Stencil
* 16 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Blue W/ Black Stencil 2 Inch X 20 Ft 4K Ratchet Strap W/ E Fittings
* High Quality Ratchet Strap* Includes E Fittings
* Assembly WLL: 1.466 Lbs
* Breaking Strength: 4,400 Lbs
* Heavy-Duty Polyester
* Blue With Black Stencil
* 20 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Yellow W/ Black Stencil 2 Inch X 12 Ft 4K Ratchet Strap W/ Trailer Plate Hooks
* High Quality Ratchet Strap* Includes Trailer Plate Hooks
* Assembly WLL: 735 Lbs
* Breaking Strength: 2,200 Lbs
* Heavy-Duty Polyester
* Yellow With Black Stencil
* 12 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Gray W/ Black Stencil 2 Inch X 16 Ft 4K Ratchet Strap W/ Trailer Plate Hooks
* High Quality Ratchet Strap* Includes Trailer Plate Hooks
* Assembly WLL: 735 Lbs
* Breaking Strength: 2,200 Lbs
* Heavy-Duty Polyester
* Gray With Black Stencil
* 16 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Blue W/ Black Stencil 2 Inch X 20 Ft 4K Ratchet Strap W/ Trailer Plate Hooks
* High Quality Ratchet Strap* Includes Trailer Plate Hooks
* Assembly WLL: 735 Lbs
* Breaking Strength: 2,200 Lbs
* Heavy-Duty Polyester
* Blue With Black Stencil
* 20 Foot Length
* 2 Inch Width
* Sold Individually
* Warranty On Ratchet Straps Against Defects In Workmanship & Material From Date Of Purchase
*** High Quality Aftermarket Replacement Part (Not OEM)***
** Manufacturer Warnings:
- Webbing strap assemblies must be protected when used on or over corners, edges and rough or sharp objects. All strap assemblies require inspection each time before they are used.
- Straps that are cut, worn or otherwise damaged shall not be used.
- Strap assemblies should never be tied into knots or allowed to become knotted.
- All Multiprens USA straps are load control devices and should not be used for overhead lifting.
- Synthetic web tie down assemblies should not be loaded in excess of the Working Load Limit. Consideration should be given to the angle from the vertical (cargo tie down to load angle) which affects working load limit capacity.
- Synthetic web tie downs shall be used, checked and adjusted during transportation of cargo per federal, state, Provencal, local and industry regulations.
- All webbing strap assemblies or systems are only as strong as the weakest component, including the point of attachment.
- When tie downs are attached directly to cargo, they should be attached symmetrically and above the cargo?s center of gravity to reduce the tendency of cargo to overturn.
- Do not repair webbing, hardware or stitching / sew patterns.
- All users must be trained in tie down selection, use and inspection, cautions to personnel, environmental effects, all applicable standards, regulations and tie down practices.
- Be alert to hazards when securing cargo.
- Tie downs should be protected from mechanical, chemical and environmental damage.
- Tie down straps should be removed from service if: The identification tag is missing or not readable. Holes, tears, cuts, snags or embedded materials are present. Broken or worn stitches in the load bearing splices. Knots in any part of the webbing. Excessive abrasive wear or crushed webbing. Signs of ultraviolet (UV) light degradation. Distortion, excessive pitting, corrosion or other damage to buckles or end fittings. Any conditions which cause doubt as to the strength of the tie down.
* This Item Is Special Order. This Item Will Not Be Able To Be Canceled And Is Non-Returnable.
Additional Information
Width Options: |
2 Inch |
Length Options: |
144 Inch |
Color: |
Blue |
Color: |
Gray |
Length Options: |
192 Inch |
Product Type: |
Cargo Control |
Length Options: |
240 Inch |
Color: |
Yellow |
Material Options: |
Polyester |
Make: |
Universal Items |
